View unanswered posts  View active topics

Page 1 of 1

[ 38 posts ] 

Author 
Message 
Oskar

Post subject: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 3:03 pm 

Joined: Mon Nov 30, 2009 1:03 pm

Hi NonTwisty Puzzles fans, Looney Gears is a strange eccentric planetary gearing system. Whereas normal planetary gear systems are symmetrical, this one has no symmetry whatsoever. This particular set of gears was the result of a challenge by Oskar to Andreas Röver in 2006. Andreas found this nice set of allprimarynumbers gears which is about 0.01% exact. At this moment (20 July 2012), it is not known whether there exist exact solutions for this type of eccentric planetary gear systems. Oskar's conjecture is that no exact solution exists. It would make a nice math graduation project to prove the conjecture or find a counter example. EDIT: Bill Somsky proved Oskar's conjecture wrong. It is actually quite easy to find exact solutions, " Somsky Gears". Watch the YouTube video of Looney Gears. Watch the animation. Watch the YouTube video of Somsky Gears. Buy the object at my Shapeways Shop. Read more at the Shapeways Forum. Check out the photos below. Enjoy! Oskar P.S. My Californian friend George Miller asked me to make a video in pouring rain. Such situation is much more rare in my country than you would expect. Finally, the right conditions were there: pouring rain and a waterproof puzzling object ready for demonstration. Attachment:
LooneyGearsv2view1.jpg [ 31.83 KiB  Viewed 9060 times ]
Attachment:
LooneyGearsv2view2.jpg [ 31.8 KiB  Viewed 9060 times ]
Attachment:
LooneyGearsv2view3.jpg [ 26.96 KiB  Viewed 9060 times ]
Attachment:
LooneyGearsv2view4.jpg [ 47.25 KiB  Viewed 9060 times ]
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .
Last edited by Oskar on Sun Dec 23, 2012 6:28 am, edited 3 times in total.


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 3:15 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

Hey Oskar, that's really crazy. Great idea using herringbone gears to keep them stable and held in. Isn't the answer to your question again the LCM(7,11,13,17) and since they are all coprime that's just 7 * 11 * 13 * 17 == 17017?
When you say these gears are about 0.01% exact do you mean that there is no tooth shape / size that makes each gear mesh perfectly? That is there is some tiny amount of "fudging" going on?
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 3:26 pm 

Joined: Mon Nov 30, 2009 1:03 pm

bmenrigh wrote: Isn't the answer to your question again the LCM(7,11,13,17) and since they are all coprime that's just 7 * 11 * 13 * 17 == 17017? Wrong. Were you just guessing? bmenrigh wrote: When you say these gears are about 0.01% exact do you mean that there is no tooth shape / size that makes each gear mesh perfectly? That is there is some tiny amount of "fudging" going on? Indeed. The amount of fudging is actually so tiny, that I did not actually fudge the design at all when I CADded it. Oskar
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 3:32 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

Oskar wrote: bmenrigh wrote: Isn't the answer to your question again the LCM(7,11,13,17) and since they are all coprime that's just 7 * 11 * 13 * 17 == 17017? Yeah I was just guessing. I see at least one mistake now though and that is assuming that you have to turn the center gear over 13 times which is obviously not right. If I can change my guess I'd go with 7 * 11 * 17 == 1309. I think I see now why it's hard to create an asymmetrical planetary gear system. The tooth size is fixed so that all of the teeth mesh together. So the number of teeth instead influences the radius of each gear. You have to find a way to pack circles with radius that are an integer ratio to each other inside of another circle with an integer ratio to them. Seems hard.
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 3:35 pm 

Joined: Mon Nov 30, 2009 1:03 pm

bmenrigh wrote: If I can change my guess I'd go with 7 * 11 * 17 == 1309. Wrong again. Like all my YouTubefan guesses so far. Instead of just randomly selecting numbers and multiplying them, you could also try and do some reasoning ...
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 4:01 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

Oskar wrote: bmenrigh wrote: If I can change my guess I'd go with 7 * 11 * 17 == 1309. Wrong again. Like all my YouTubefan guesses so far. Instead of just randomly selecting numbers and multiplying them, you could also try and do some reasoning ... Yeah it's more complex than I assumed Watching your video over and over, after you do 1 turn with the 13 gear, if the gears were fixed in space then the 11 gear would have made more than one revolution. Because of the interaction with the outer gear though it ends up going through less than a full revolution. I need to figure out the rule that governs what rate an outer gear does a revolution which seems dependent on both the central gear and the outermost enclosing gear.
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 5:44 pm 

Joined: Mon Mar 30, 2009 5:13 pm

(13*17)*(13*11)*(13*7)/13 = 221221 turns of the central cog per complete cycle. Note the 37 cog does not factor into the equation, but its circumference has to be rounded ("fudged") slightly to the nearest integer number of cogs. Is that right? EDIT: Sorry, forget this post  I forgot that the planets rotate about the sun as the sun turns within the stationary frame. I have recalculated, and posted the correct answer below. What a challenge this has been!
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson
Last edited by KelvinS on Fri Jul 20, 2012 7:40 pm, edited 1 time in total.


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 7:13 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

The more I've thought about this, the less sure I am of anything.
I believe the function that describes how much an orbiting gear turns for every turn of the 13 gear is nonlinear.
The best I've been able to come up with is: f(x) = (13 / x) * 2 * (13 / (37 + x))
Which reduces to: f(x) = 338 / (x^2 + 37*x)
Unfortunately this function doesn't exactly match (but it's rather close) to Oskar's video. I don't know why this is such a hard problem. I must be approaching it wrong.
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 7:37 pm 

Joined: Mon Mar 30, 2009 5:13 pm

OK, forget my last post. The answer is: 7*11*17*13/(13+37) = 340.34 turns of the central cog to realign all 4 internal cogs with each other. However, to get rid of the two decimals (about 1/3 of a turn) and make all these cogs vertical again, you need to multiply this by 3, to give: 1021.02 turns of the central cog per complete cycle of all 4 internal cogs, so that they are perfectly aligned and *almost* in their original vertical starting position. Or if you want an *exact* solution, then you have to multiply 340.34 by 50 instead of 3, which gives 17017 turns as calculated above by bmenrigh  so his answer was technically correct, even if it was just a guess.
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


bobthegiraffemonkey

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 8:31 pm 

Joined: Fri Jan 29, 2010 2:34 pm Location: Scotland, UK

I'm sleepy, but I found this interesting so I gave it a go. Here's my answer: 1769
Explanation: Ignore the red wheel for now. Look at the other 3 meshing on the outer wheel. They are always the same distance apart. After moving them by 7*11*17=1309 cogs in a particular direction, they will all be upright again. However, the 13 gear won't be, so we multiply by 13 to get 17017 cogs moved to get all upright. But the red cog hasn't rotated 17017 times. Consider the 7 cog and the 13 cog, fixed relative to each other. The 7 cog moves by 17017 cogs, so the 13 cog rotates 1309 times. Then, keep the 13 cog in place, and drag the 7 cog round it by the number of times the 7 cog goes round the 37 cog. This is approximately calculated at 460, and I assume I can round this due to the fudge factor involved. Adding these rotations gives the answer of 1309+460=1769.
I think my reasoning is fairly sound, although lack of alertness may have introduced some silly errors ...


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 8:55 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

The trouble I'm having with any straightforward analysis is that the assumption that the rate at which the 7 or 11 or 17 gear turns is just some fixed ratio with the 13 or 37 gear. For example, by looking at Oskar's video, after one turn of the 13 gear it appears that:  The 7 gear turns 1.125 times
 The 11 gear turns 0.625 times
 The 17 gear turns 0.3125 times
These are not a linear relationship to their number of teeth. Their circular motion due to the interaction with the outer 37 gear is affecting the 13:N ratio in some way. It seems like the ratio that each gear spins compared to the 13 gear has in some way to do with the ration between the 13 and 37 gear.
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 9:04 pm 

Joined: Mon Mar 30, 2009 5:13 pm

bmenrigh wrote: It seems like the ratio that each gear spins compared to the 13 gear has in some way to do with the ratio between the 13 and 37 gear. Yes, 13/(13+37), hence my calculation above. See: http://en.wikipedia.org/wiki/Epicyclic_gearing
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 9:15 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

KelvinS wrote: bmenrigh wrote: It seems like the ratio that each gear spins compared to the 13 gear has in some way to do with the ratio between the 13 and 37 gear. Yes, 13/(13+37), hence my calculation above. See: http://en.wikipedia.org/wiki/Epicyclic_gearingSo using this math, how many times does the 7 gear spin when the 13 gear spins once?
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


cubedude76

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 9:53 pm 

Joined: Sun Mar 06, 2011 12:46 pm Location: Wichita

well the 13 gear in the middle doesnt actually rotate on its axis 360 degrees. it gets part of its rotation from its changing position and it gets the other part of its rotation be actually spinning on its own axis. I hope this picture explains what I mean.
The first picture shows the gear getting its rotation from its location changing. the second picture shows the rotation the gear gets from spinning on its axis. thats why the gears dont move 13 teeth in a single rotation. if you could figure out how much it spins when you make a rotation that might help.
Attachments: 
gears.jpg [ 97.82 KiB  Viewed 8790 times ]

_________________ Feel free to visit my Shapeways Shop! Pentaminx Auction


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Fri Jul 20, 2012 11:48 pm 

Joined: Mon Mar 30, 2009 5:13 pm

bmenrigh wrote: KelvinS wrote: bmenrigh wrote: It seems like the ratio that each gear spins compared to the 13 gear has in some way to do with the ratio between the 13 and 37 gear. Yes, 13/(13+37), hence my calculation above. See: http://en.wikipedia.org/wiki/Epicyclic_gearingSo using this math, how many times does the 7 gear spin when the 13 gear spins once? Sorry it's a bit more complicated than I first thought, but now I've managed to figure out the math. Here goes: Each full turn of a central cog with s teeth within a fixed outer annual cog with a teeth will result in n turns of a bridging cog with p teeth, where: n = (a  p) / p * s / (s + a) In this case s = 13, a = 37, and p = 7, 11 or 17, so: For p = 7: n = (37  7) / 7 * 13 / (13 + 37) = 1.114286 For p = 11: n = (37  11) / 11 * 13 / (13 + 37) = 0.614545 For p = 17: n = (37  17) / 17 * 13 / (13 + 37) = 0.305882 Note that the lowest common denominator required to give a whole number in each case is: 7*11*17*5*5 = 32725 turnsSo 32725 full turns of central cog with 13 teeth gives: 32725 * 1.114286 = 36465 full turns of bridging cog with 7 teeth 32725 * 0.614545 = 20111 full turns of bridging cog with 11 teeth 32725 * 0.305882 = 10010 full turns of bridging cog with 17 teeth
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sat Jul 21, 2012 12:43 am 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

KelvinS wrote: Sorry it's a bit more complicated than I first thought, but now I've managed to figure out the math. Here goes:
Each full turn of a central cog with s teeth within a fixed outer annual cog with a teeth will result in n turns of a bridging cog with p teeth, where:
n = (a  p) / p * s / (s + a) [...] Great job, I could not figure that equation out. I tried many close / similar ideas but I was mostly guessing. I don't understand the (a  p) / p term. Can you explain how you derived this the full formula?
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sat Jul 21, 2012 12:50 am 

Joined: Mon Mar 30, 2009 5:13 pm

bmenrigh wrote: KelvinS wrote: Sorry it's a bit more complicated than I first thought, but now I've managed to figure out the math. Here goes:
Each full turn of a central cog with s teeth within a fixed outer annual cog with a teeth will result in n turns of a bridging cog with p teeth, where:
n = (a  p) / p * s / (s + a) [...] Great job, I could not figure that equation out. I tried many close / similar ideas but I was mostly guessing. I don't understand the (a  p) / p term. Can you explain how you derived this the full formula? Yes, assume that the bridging cogs are all fixed in position and spin round their axes so that the outer ring turns as you rotate the central cog, then you can easily calculate rotation of the outer ring as well as each bridging cog for each turn of the central cog. However, you then have to subtract anticlockwise rotation of the outer ring from anticlockwise rotation of the bridging cog, and add anticlockwise rotation of the outer ring to clockwise rotation of the central cog, so that all rotations are measured relative to a fixed outer ring. The complexity arises from using the wrong frame of rotation reference: If you try to think about the outer ring being still from the start then things get confusing because they are moving as well as rotating. It's a bit like trying to calculate the path of the moon by usinig the sun as the frame of reference, rather than the earth. Therefore you have to imagine the bridging planetary cogs as being fixed in position but spinning, do the basic calculations, and only then switch the frame of reference. The addition and subtraction terms come from that last step. You can rewrite the formula above as follows, to see where it comes from: n = ( s / p  s / a) / ( 1 + s / a ) Think of this as the number of bridging cog turns ( s / p ) per central cog turn ( 1 ), after both of these have been adjusted by the number of outer ring turns per central cog (+/ s / a, depending on relative direction). It's a great problem, much trickier than I thought, has kept me entertainted for hours.
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson
Last edited by KelvinS on Sat Jul 21, 2012 11:51 am, edited 2 times in total.


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sat Jul 21, 2012 10:20 am 

Joined: Mon Nov 30, 2009 1:03 pm

KelvinS wrote: ... 7*11*17*5*5 = 32725 turns ... That is 100% correct! Congratulations for being the first person solving this problem. The two drawings below show the effect of those 32725 turns. If you want to get all gears also back to their original position, you'll have to do another 32725 turn, which makes 65450 turns in total. Oskar Start position Attachment:
Looney Gears  start.jpg [ 94.32 KiB  Viewed 8617 times ]
After 32725 turns Attachment:
Looney Gears  after 32725 turns.jpg [ 94.3 KiB  Viewed 8617 times ]
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .


Top 


RubixFreakGreg

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sat Jul 21, 2012 10:42 am 

Joined: Sat Jan 16, 2010 11:48 am Location: In Front Of My Teraminx (saying WTF?)

Oskar wrote: That is 100% correct! Congratulations for being the first person solving this problem. The two drawings below show the effect of those 32725 turns. If you want to get all gears also back to their original position, you'll have to do another 32725 turn, which makes 65450 turns in total.
Oskar
Oskar, could you please make a demonstration video of the cycle please ?
_________________ My Shapeways Shop! My Designs My Official Results My Website on Twisty Puzzles with Gears
Grégoire Pfennig


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sat Jul 21, 2012 10:55 am 

Joined: Mon Nov 30, 2009 1:03 pm

RubixFreakGreg wrote: Oskar, could you please make a demonstration video of the cycle please ? If you make that video and show it unedited on YouTube, then I shall refund your purchase. Note that I expect you to be counting turns out loud. Oskar
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sat Jul 21, 2012 11:29 am 

Joined: Mon Mar 30, 2009 5:13 pm

Oskar wrote: KelvinS wrote: ... 7*11*17*5*5 = 32725 turns ... That is 100% correct! Congratulations for being the first person solving this problem. The two drawings below show the effect of those 32725 turns. If you want to get all gears also back to their original position, you'll have to do another 32725 turn, which makes 65450 turns in total. Oskar Thanks. Now who can work out how many possible permutations there are to assemble all four gears within the outer ring, with each cog in any position and orientation? That should tell us what % of all permutations can be reached within 65450 turns (and the probability of ever being able to align all the numbers) from any given starting position.
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


RubixFreakGreg

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sat Jul 21, 2012 1:27 pm 

Joined: Sat Jan 16, 2010 11:48 am Location: In Front Of My Teraminx (saying WTF?)


Top 


darryl

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Jul 23, 2012 12:56 pm 

Joined: Fri Feb 18, 2000 8:50 am Location: chicago, IL area U.S.A

Would it be possible to make this in acrylic for cheaper? I suppose instead of using herringbone gears, it could just sit flat.
d


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Jul 23, 2012 1:32 pm 

Joined: Mon Nov 30, 2009 1:03 pm

darryl wrote: Would it be possible to make this in acrylic for cheaper? The original 2006 version was lasercut in MDF. Oskar Attachment:
LooneyGears2006version.jpg [ 43.92 KiB  Viewed 8245 times ]
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Jul 23, 2012 1:37 pm 

Joined: Mon Mar 30, 2009 5:13 pm

darryl wrote: Would it be possible to make this in acrylic for cheaper? I suppose instead of using herringbone gears, it could just sit flat. Nice idea. I was also wondering about more complex versions, with more cogs...
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Jul 23, 2012 1:57 pm 

Joined: Mon Nov 30, 2009 1:03 pm


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Jul 23, 2012 2:06 pm 

Joined: Mon Mar 30, 2009 5:13 pm

Oskar wrote: KelvinS wrote: I was also wondering about more complex versions, with more cogs... Like this? Exactly, but asymmetric... and you may as well ask the same question (turns per cycle?), but make it a bit more difficult this time. Also, I see room in there for 3 more smaller cogs.
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sun Aug 05, 2012 3:16 am 

Joined: Mon Nov 30, 2009 1:03 pm

Bill Somsky surprised me with an analysis of the Looney Gears. 1) He found an algorithm to construct exactly fitting Looney Gears. Let's call those Somsky Gears. 2) He found an exact solution for the Looney Gears set of 37+13+17+11+7, and managed to find an exact fit for an additional 13 gear. 3) He found a set of Somsky Gears having six planetary gears. Amazing! Oskar Attachment:
37130713171110.36618080.png [ 4.33 KiB  Viewed 7788 times ]
Attachment:
G34181086.gif [ 264.42 KiB  Viewed 7788 times ]
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .


Top 


darryl

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 12:48 pm 

Joined: Fri Feb 18, 2000 8:50 am Location: chicago, IL area U.S.A

Unbelievable! I'd say this should be patented, but I suppose it needs some sort of real world application other than just to look at in awe.
d


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 1:25 pm 

Joined: Mon Mar 30, 2009 5:13 pm

darryl wrote: Unbelievable! I'd say this should be patented, but I suppose it needs some sort of real world application other than just to look at in awe.
d I agree, however you can't patent something after it has been published, except in the US where you get 12 months grace. Meanwhile, if there's no intention to patent then I would love to see the solution/equation that determines what configurations are possible, just out of curiosity. I assume any participation of pi in the equation cancels out to give the perfect integer solutions?
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


wwwmwww

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 1:46 pm 

Joined: Thu Dec 02, 2004 12:09 pm Location: Missouri

Oskar wrote: At this moment, it is not known whether there exist exact solutions for this type of eccentric planetary gear systems. Oskar's conjecture is that no exact solution exists. It would make a nice math graduation project to prove the conjecture or find a counter example. Oskar wrote: Bill Somsky surprised me with an analysis of the Looney Gears. 1) He found an algorithm to construct exactly fitting Looney Gears. Let's call those Somsky Gears. So are we saying Oskar's conjecture has been disproven? Who is Bill Somsky? Do we have a nice dissertation or paper to expect to come out of this work? It sounds very interesting and I'd be interested in reading it if so. Carl
_________________ 


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 4:28 pm 

Joined: Mon Nov 30, 2009 1:03 pm

darryl wrote: I'd say this should be patented, but I suppose it needs some sort of real world application Strangely, whereas Bill cannot patent his Somskygeargenerating algorithm (at least not according to European patent law, that sortof excludes software algorithms), still someone could design a twisty puzzle using Somsky gears, and patent that (as twistypuzzle mechanisms can be patented). So start designing now! KelvinS wrote: you can't patent something after it has been published Well, Bill has disclosed his algorithm to me, but he hasn't published it yet. You have only seen some verifiable examples. Given these examples, can you guess or reverseengineer his algorithm? It is quite elementary and elegant. wwwmwww wrote: So are we saying Oskar's conjecture has been disproven? Who is Bill Somsky? Do we have a nice dissertation or paper to expect to come out of this work? Yes, my conjecture has been convincingly disproven. Bill is one of my YouTube fans, which is about all that I know about him. And yes, Bill and I are thinking about writing a paper. Oskar
_________________ Oskar's home page, YouTube, Shapeways Shop, Puzzlemaster, and fan club .


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 4:37 pm 

Joined: Mon Mar 30, 2009 5:13 pm

A paper would be fantastic, though I do think you should seriously consider a patent before publishing the algorithm: have a think about significant applications besides 'just' puzzles, especially in engines, etc.
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 4:55 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

Oskar wrote: Bill Somsky surprised me with an analysis of the Looney Gears. 1) He found an algorithm to construct exactly fitting Looney Gears. Let's call those Somsky Gears. 2) He found an exact solution for the Looney Gears set of 37+13+17+11+7, and managed to find an exact fit for an additional 13 gear. 3) He found a set of Somsky Gears having six planetary gears. Amazing! Hi Oskar, I have a few questions that I hope you can clarify. When I was looking at trying to solve your original problem, I was operating under the assumption that the number of teeth for each gear is the only factor controlling the diameter of the gear. That is the ratio of the radius between an 11 tooth gear and a 13 tooth gear is always constant. I also assumed that for a given set of gears, say, outer 37, inner 7, 11, 13, and 17 that there would only be one way to place the inner sun gear and outer planet gears. Finally, I'm also assuming that for your 4planet animation that extra 13 gear planet isn't necessary and for your 6planet animation you have 2 of each gear and I assume you can pull out each duplicate and still have a perfectly good solution. So given those assumptions, how is it that your 37 outer gear, 13 sun gear, {7, 11, 17} planets were not an exact solution but the exact solution you show is the same thing with an extra 13th planet (which I assume can be removed). It seems like there is some hidden difference between your approx solution and this exact one and I don't see it.
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 4:59 pm 

Joined: Mon Mar 30, 2009 5:13 pm

bmenrigh wrote: So given those assumptions, how is it that your 37 outer gear, 13 sun gear, {7, 11, 17} planets were not an exact solution but the exact solution you show is the same thing with an extra 13th planet (which I assume can be removed). It seems like there is some hidden difference between your approx solution and this exact one and I don't see it. Check out the relative positions of the planetary gears: they gain or lose space as you move them around the offcenter sun.
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson
Last edited by KelvinS on Mon Aug 06, 2012 5:08 pm, edited 2 times in total.


Top 


Brandon Enright

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 5:00 pm 

Joined: Thu Dec 31, 2009 8:54 pm Location: Bay Area, California

KelvinS wrote: Check out the relative positions of the planetary gears: they gain or lose space as you move them around the offcenter sun. Yes I see that but their relative positions didn't factor into your formula at all. Can Oskar just take out the 4 gears he has printed and put them in differently and have an exact solution?
_________________ Prior to using my real name I posted under the account named bmenrigh.


Top 


KelvinS

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Mon Aug 06, 2012 5:02 pm 

Joined: Mon Mar 30, 2009 5:13 pm

bmenrigh wrote: KelvinS wrote: Check out the relative positions of the planetary gears: they gain or lose space as you move them around the offcenter sun. Yes I see that but their relative positions didn't factor into your formula at all. Can Oskar just take out the 4 gears he has printed and put them in differently and have an exact solution? Yes, I believe so, but let's see what Oskar says. I think the original problem came from assuming that the 3 planetary gears should be set about 120 degrees apart to keep the thing stable, so it was this angle which caused the misfit, not the gears themselves. But, while Oskar could take out the 4 gears he has printed and put them in differently to get an exact solution, it would not be very stable because the sun gear would not be supported on one side, hence the additional gear.
_________________ If you want something you’ve never had, you’ve got to do something you’ve never done  Thomas Jefferson


Top 


Oskar

Post subject: Re: Looney Gears by OSKAR & ANDREAS Posted: Sun Dec 23, 2012 6:10 am 

Joined: Mon Nov 30, 2009 1:03 pm


Top 



Page 1 of 1

[ 38 posts ] 

Who is online 
Users browsing this forum: No registered users and 4 guests 

You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum


