Online since 2002. Over 3300 puzzles, 2600 worldwide members, and 270,000 messages.

TwistyPuzzles.com Forum
 It is currently Tue Mar 11, 2014 4:28 pm

 All times are UTC - 5 hours

 Page 1 of 1 [ 10 posts ]
 Print view Previous topic | Next topic
Author Message
 Post subject: Megamorphix 3D Printed - Part 1Posted: Fri Nov 16, 2012 7:23 am

Joined: Sun Mar 15, 2009 12:00 am
Location: Jarrow, England
Hi guys. This is a two part post because of the number of images. This part concerns the design, while the second part will be about the building of a Megamorphix. I just thought that you may be interested in the entire process of puzzle building the way I do it.

Inspired by this post and the release of the Witeden mini 4x4x4 (11.5mm cubies) I decided to make a Megamorphix. I don't think that I have the building skills to make one from plastic sheet (and it would be very tricky because of the small cubie size) so I of course used Google SketchUp to design the extensions.

First, create a cube of edge length 11.5m. Yes, that is meters. I do the design 1000x full size to avoid some nasty quirks SU has when it tries to create very small triangles. The scaling is taken care of during the transfer to Shapeways.
Attachment:

Megamorphix 000.png [ 98.65 KiB | Viewed 2024 times ]
Next, duplicate the cubie to make a 4x4x4.
Attachment:

Megamorphix 001.png [ 159.98 KiB | Viewed 2024 times ]
Now, I define where the turning planes of the cube are, which are then going to be used to create the extension pieces.
Attachment:

Megamorphix 002.png [ 137.45 KiB | Viewed 2024 times ]
In this build I will have to truncate the 4x4x4 across the corner cubies as shown.
Attachment:

Megamorphix 003.png [ 152.33 KiB | Viewed 2024 times ]
This shows the required truncation. The center triangle forms the center piece on the four faces of the final puzzle.
Attachment:

Megamorphix 004.png [ 155.17 KiB | Viewed 2024 times ]
Using the truncated faces, I add guides which will intersect at the corners of the required tetrahedral shape. As you can see, sorting which intersections I need can be a bit awkward, but once you find one edge the rest follow easily.
Attachment:

Megamorphix 005.png [ 157 KiB | Viewed 2024 times ]
The finished tetrahedron, with the outline of the truncated cube shown inside.
Attachment:

Megamorphix 007.png [ 133.15 KiB | Viewed 2024 times ]
Now I add the turning planes of the 4x4x4, which will become the cutting planes through the tetrahedron, to form the extensions required.
Attachment:

Megamorphix 008.png [ 136.26 KiB | Viewed 2024 times ]
Using the planes, I cut out and isolate the extension pieces needed. In the Megamorphix, five different pieces are required. This is the large corner part (4 needed).
Attachment:

Megamorphix 009.png [ 95.88 KiB | Viewed 2024 times ]
Now I have to subtract the part of the cubie to which this piece will be attached, using the cubies I drew before.
Attachment:

Megamorphix 010.png [ 87.75 KiB | Viewed 2024 times ]
Now, this is where SU shows its weaknesses when compare to programs like Solidworks. I need to create a thin shell (I use 1mm thick) to minimise the costs of Shapeways printing. SU has no native shell tool, but you can download free Ruby plugins which add this functionality. They usually work OK on simple shapes like this, but can go horribly wrong on more complex ones. The image below shows a wireframe view of the shelled shape.
Attachment:

Megamorphix 011.png [ 124.33 KiB | Viewed 2024 times ]
I now add fillets. Again, this has to be done using a plugin, and works well for this sort of shape. But again, it can be more difficult for complex solids, which may need a lot of manual work to tidy them up.
Attachment:

Megamorphix 012.png [ 181.34 KiB | Viewed 2024 times ]
Here I have added some small holes which connect the inner and outer "shells" of the part together. These make a manifold object and allow Shapeways to extract the unused nylon powder which would otherwise be trapped inside. At this point the part should be watertight and manifold. I use a plugin called SolidInspector to check this.
Attachment:

Megamorphix 013.png [ 192.48 KiB | Viewed 2024 times ]
This is then exported to an stl file using yet another free plugin. I can now load the stl file into netfabb basic to check that everything is OK.
Attachment:

Megamorphix 015.png [ 53.85 KiB | Viewed 2024 times ]
The next part can be very frustrating. In order to get Shapeways discount, the model density must be greater than 10%. So, sometimes I have to carefully arrange the parts to maximise the packing to achieve this. As you may notice from the image below, I added the yellow sticker template to the design, which added material to the model without increasing the overall size, thus bringing the density over 10%.
Attachment:

Megamorphix 016.png [ 213.27 KiB | Viewed 2024 times ]
Now, export the whole thing to an stl file, check it again using netfabb and upload it to Shapeways (remembering to specify the units as mm!).

In part 2, I will show some pictures of the build process using the printed parts and the Witeden cube.

_________________
My Shapeways Shop: http://www.shapeways.com/shops/gus_shop

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 16, 2012 12:19 pm

Joined: Mon Mar 07, 2011 11:08 pm
If this works, are you going to sell the extensions on Shapeways?

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 16, 2012 2:21 pm

Joined: Sun Mar 15, 2009 12:00 am
Location: Jarrow, England
I don't see why not. But as the printed pieces need to be added to a modified 4x4x4, that may put a lot of people off buying them.

_________________
My Shapeways Shop: http://www.shapeways.com/shops/gus_shop

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 16, 2012 3:33 pm

Joined: Sun Jan 09, 2011 1:39 pm
Location: frederick MD. USA
is that sketch up or sketch up pro?

_________________
my shapeways shop http://www.shapeways.com/designer/thecube1313

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 16, 2012 4:24 pm

Joined: Sun Mar 15, 2009 12:00 am
Location: Jarrow, England
It's SketchUp 8 free edition. I wish there was a Solidworks free edition

_________________
My Shapeways Shop: http://www.shapeways.com/shops/gus_shop

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 16, 2012 5:10 pm

Joined: Sun May 29, 2011 2:56 pm
Location: New York
Gus wrote:
I don't see why not. But as the printed pieces need to be added to a modified 4x4x4, that may put a lot of people off buying them.

Just to clarify (as I will probably be buying this), you need to make a half truncated cube out of the 4x4 first?

-Doug

_________________

Recent videos: Master Axis Cube | 4x4x2 Solve | 3x3x3 Triangular Prism

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 16, 2012 5:34 pm

Joined: Sun Mar 15, 2009 12:00 am
Location: Jarrow, England
Essentially yes, but you need to do the cuts a little (1mm) deeper than the exact cuts shown in the images above. I'll explain about this in part 2.

_________________
My Shapeways Shop: http://www.shapeways.com/shops/gus_shop

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Thu Nov 22, 2012 12:36 pm

Joined: Mon Apr 12, 2010 2:57 pm
I would definitely buy the extentions. The pictures explain everything. I have built my mastermorphix, but it is so horrid that I scrapped it for the most part. I am looking forward to part two.

_________________
How much wood would a woodchuck chuck if a woodchuck could chuck wood?

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 23, 2012 2:51 am
Any news on when we can see part 2?

Top

 Post subject: Re: Megamorphix 3D Printed - Part 1Posted: Fri Nov 23, 2012 4:00 am

Joined: Sun Mar 15, 2009 12:00 am
Location: Jarrow, England
I am still waiting for the stickers from Dr. Sticker, I ordered them on 8th and they were posted on the 9th. Naughty postal service

_________________
My Shapeways Shop: http://www.shapeways.com/shops/gus_shop

Top

 Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost timeSubject AscendingDescending
 Page 1 of 1 [ 10 posts ]

 All times are UTC - 5 hours

#### Who is online

Users browsing this forum: Google Adsense [Bot], The Casual Cuber and 5 guests

 You cannot post new topics in this forumYou cannot reply to topics in this forumYou cannot edit your posts in this forumYou cannot delete your posts in this forumYou cannot post attachments in this forum

Search for:
 Jump to:  Select a forum ------------------ Announcements General Puzzle Topics New Puzzles Puzzle Building and Modding Puzzle Collecting Solving Puzzles Marketplace Non-Twisty Puzzles Site Comments, Suggestions & Questions Content Moderators Off Topic