From my last topic: Mini Hexis.

I made this puzzle for a week. Enjoy it. No stickered too.

Let me give name for this one Kevin! Let us Call it "Kevin's Off-Set Cube"

after off-set cube series like Okamoto's Off-set Skewb and Anthony Greenhills's Off-set 1

Why dont we Call this original Mod of your The "Kevin's Off-set Cube"...

Well, that's a good idea.

I would like to have a name for this puzzle without place for my name.
Hmm, I chose the name for my puzzle but I think it's so...: ITA Cube - Incredible Transformation of Axis Cube.
Do you think it's good?

Well its Good too, but the ITA is a bit Abbreviation and people might get curious about it unless they would ask! Giving name with inventor's name on the cube is the most remarkable specially when they made it original by own design! so if you allowed me in case "The Off-Set Cube" is the best Name for it...



Regards

.Ok, let's give this puzzle that name. Thank you, Pinoycuber27 for this pretty name.
I will post some scramble later, I get no camera right now.

Yes that Cube deserve that name ...


Offset Skewb

Offset -1


and Now the "Offset Cube"....


i cant want to see in get stickered and Scramble as well...

Of course, as soon as possible, I will give my friend and he will stick it for me. He has a sticker cutter machine (:?: does it call by that name?).

YEs, but me and Hidetoshi-san we used to called it "Sticka-Cutter"...

I liked the idea of Kevin's ITA cube, that sounds cool if you pronounce it 'eye-ta'.

Alex

How about the name Kevin's ITA off-set Cube?
Is it alright?

Congratulations!!

Finally it's done, and it's a very clean built.. Good job!!!
How about, its name is "Kevin's Maxis Cube", that's the name that I have planned when I plan to build it, because it's the continuation of the axis cube.. But, you are the truly inventor.. You are a good puzzle builder.. Congratulations again!!!

Oh, thank you very much for these words. However you have a plan to make it, so you are also an inventor.
Let's make one for yourself and put it into collection.

No, you are the inventor kevin..
I have no time to make that very consuming time puzzle.. I don't have much passion like you... , so you are the one who can bring this cube from a dream to this world... Good job man..

Now, I'm stucked with my built.. I make an axis dino cube, but when it's getting done, the rotation movement was blocked by the extended side, and it' all unpredicted because I don't have any CAD, or any program that help me look out the finished puzzle and I also don't sketch it!! So, I confused now, what should I do because I have taken a lot lot of time with this....

Well, I'm so sorry. I hope that I can help you but I have never seen this puzzle before. In my country, Vietnam, this puzzle is not interesting.
Let's think about it. Now, you cut this puzzle like 3x3x3 > Hexagonal Dipyramid > Axis. If you don't have any problems when you are cutting the Hexagonal Dipyramid, I can sure that you can build this puzzle exactly like you want. When you extend other sides, let's use something flat to block the movement ways of the puzzle then you can follow these ways to extend. Of course, you must sure that these extension part will not block the movement ways first.

However sorry if I have a wrong answer cause I cannot know what you meant.

Thank's for your suggestions,

I can built it into HD, but when I extended it it, the rotation is blocked with the other extension (because the dino cube rotation is different from a 3*3), maybe I must finished it first and then sand the blocked area till it can move properly.. But I don't sure about that... However, I'm an Indonesian, so we are same from ASEAN...

Here are some patterns but still blank , no sticker too . Next to it is My DIY Type New A3. I'm also a speed cuber .










Under is a Conan comic . However, I'm still a student.